DPChallenge: A Digital Photography Contest You are not logged in. (log in or register
 

DPChallenge Forums >> General Discussion >> The "Whattheheckizzit?" game
Pages:   ... [170] [171] [172] [173] [174] [175] [176] [177] [178] ... [265]
Showing posts 4326 - 4350 of 6612, (reverse)
AuthorThread
10/12/2012 12:16:18 PM · #4326
It is neither a part of a gun, nor part of a welder. Ben is onto one of the key clues about its origin, however.
10/12/2012 12:24:03 PM · #4327
Looks like the front of a gun. Also looks to have met up with some thermite or another similar incendiary. Also seems that it may have had a rest on the bottom of a body of water for a while afterwards.
10/12/2012 12:25:55 PM · #4328
Hmm, could also be a pipe that was completely blocked by crap, then opened up as a display item or for investigation.
10/12/2012 12:32:59 PM · #4329
Y'all are on the right track with the ideas about being subjected to high heat. Also true that it was immersed in liquid for a time. An additional hint: the piece of the item was found as-is. It was not cut or otherwise excised from the original object. The diameter of the once-tubular shell is about 1/2 inch, or about 12mm.
10/12/2012 12:37:20 PM · #4330
Railing from a shipwreck
10/12/2012 12:45:49 PM · #4331
Originally posted by TrollMan:

Railing from a shipwreck


Nope, getting colder ;-)
10/12/2012 12:46:42 PM · #4332
I will say that the original object performed some active function, not passive like a guard, support or railing.
10/12/2012 01:05:08 PM · #4333
fireplace gas pipe
10/12/2012 01:08:54 PM · #4334
Originally posted by kawesttex:

fireplace gas pipe


Nope. In fact, I'll go further, not a pipe, e.g. its purpose was not to transport a fluid or gas.
10/12/2012 01:29:42 PM · #4335
under water electric wire that shorted on it's ground sleeve?
10/12/2012 01:31:34 PM · #4336
Looks like it's galvanized...
10/12/2012 01:41:45 PM · #4337
Originally posted by bhuge:

under water electric wire that shorted on it's ground sleeve?


I'm going to take this answer!
It's a section of an immersed heating element. The element shorted to the case, causing localized run-away heating. Imagine how much heat had to be dissipated to melt a stainless-alloy case while immersed in fluid! The carnage only stopped when a 3-inch chunk actually fell out of the heating element, and that is the piece you see here.
10/12/2012 01:59:21 PM · #4338
I have a knack for winning when I'm at work without a camera. Someone go ahead and post something if you have it ready.
10/12/2012 01:59:29 PM · #4339
Originally posted by kirbic:

Originally posted by bhuge:

under water electric wire that shorted on it's ground sleeve?


I'm going to take this answer!
It's a section of an immersed heating element. The element shorted to the case, causing localized run-away heating. Imagine how much heat had to be dissipated to melt a stainless-alloy case while immersed in fluid! The carnage only stopped when a 3-inch chunk actually fell out of the heating element, and that is the piece you see here.


Holy shit... I should have thought of that, looked coppery in the middle, but couldn't figure it out.

Might I ask what this was in? That's damned impressive.
10/12/2012 02:14:48 PM · #4340
Originally posted by Cory:

Might I ask what this was in? That's damned impressive.


It was the main sump heater in a solvent "vapor degreaser." That piece of equipment was decommissioned and scrapped a few years ago now, but I think the heater was operating at 480V.
Luckily the solvent was non-flammable, but I sure wouldn't have wanted to be breathing what was coming off that sump during the failure!
10/12/2012 02:29:12 PM · #4341
Originally posted by bhuge:

under water electric wire that shorted on it's ground sleeve?


Wow - impressive guess!
10/12/2012 02:38:46 PM · #4342
Originally posted by TrollMan:

Originally posted by bhuge:

under water electric wire that shorted on it's ground sleeve?


Wow - impressive guess!


I thought so too... especially since it stumped Cory!

ETA: In fact, the only way I'd have been more satisfied with the "stumping power" of that one would have been if it had also stumped Waddy :-) I'm still smirking, LOL.

Message edited by author 2012-10-12 14:41:44.
10/12/2012 03:07:28 PM · #4343


This may be too easy, so I expect a rather specific answer.

Message edited by author 2012-10-12 15:07:57.
10/12/2012 03:10:35 PM · #4344
The gold embossing on a US bill, a $20 I think
10/12/2012 03:19:48 PM · #4345
Originally posted by Spork99:

The gold embossing on a US bill, a $20 I think


Yeah, but what year? ;)
10/12/2012 03:20:19 PM · #4346
Originally posted by Cory:

Originally posted by Spork99:

The gold embossing on a US bill, a $20 I think


Yeah, but what year? ;)


You're up btw
10/12/2012 04:02:42 PM · #4347
Let it hereby be known that I will no longer be taking any crap from Cory regarding submissions to this thread using the MP-E65 :-)
10/12/2012 04:07:32 PM · #4348


Have fun.

Message edited by author 2012-10-12 16:08:56.
10/12/2012 04:12:32 PM · #4349
Originally posted by Spork99:

Have fun.


The rollers on a Polaroid film camera back.
10/12/2012 04:17:00 PM · #4350
Originally posted by kirbic:

Originally posted by Spork99:

Have fun.


The rollers on a Polaroid film camera back.


Which one?

Pages:   ... [170] [171] [172] [173] [174] [175] [176] [177] [178] ... [265]
Current Server Time: 08/22/2025 06:14:30 PM

Please log in or register to post to the forums.


Home - Challenges - Community - League - Photos - Cameras - Lenses - Learn - Help - Terms of Use - Privacy - Top ^
DPChallenge, and website content and design, Copyright © 2001-2025 Challenging Technologies, LLC.
All digital photo copyrights belong to the photographers and may not be used without permission.
Current Server Time: 08/22/2025 06:14:30 PM EDT.